Murphy Lube Level Maintainer LM2000 Bedienungsanleitung PDF herunterladen (Seite 2)

LM-00011N page 2 of 4

TYPICAL INSTALLATION

DIMENSIONS

1/2 in. Electrical

Female Conduit

Connection

Crankcase

Balance Vent

1/2 NPTF

4-5/8 in.

(117 mm)

4-1/2 to 5-3/16 in.

(114 to 132 mm)

Oil Inlet

Connection

1/2 NPTF

Oil Outlet

Connection

3/4 NPTF

3/8 NPTF

LM2000S

3/8 NPTF

LM2000S

2-7/8 in.

(73 mm)

2-1/4 in.

(57 mm)

Oil Inlet

Connection

1/2 NPTF

Oil Outlet

Connection

3/4 NPTF

3/8 NPTF

LM2000S

LM2000

Mounting the LM2000

NOTE: Mount the LM2000 as close as possible to the crankcase.

The following instructions are based on the usage of the pipe and universal

mounting brackets shown above.

Pipe Bracket Mounting (15000238)

1. Mount a nominal 1/2 inch (13 mm) diameter pipe to the base of the engine.

2. Install the pipe bracket to the LM2000 using two 1/4-20 UNC x 1 inch

bolts, nuts and lock washers supplied. See Figure 1A.

3. Slip the LM2000 onto the pipe and install the two adjustment bolts. Each

bolt consists of a 1/4-20 UNC x 1 in. bolt, nuts and lock washers. See

Figure 1B. DO NOT tighten the adjustment screws too tightly because

you will have to adjust the LM2000 later in the installation process.

Mounting with Universal Bracket (15000370)

The universal bracket has two mounting methods: base mounting or

pan mounting.

Base Mounting

1. Install the universal bracket to the base as shown in Figure 2A using two

flat washers and two 5/16 inch dia. bolts or others as necessary.

2. Mount the LM2000 to the universal bracket using two 1/4-20 UNC x 1-

1/4 inch (32 mm) bolts, nuts and lock washers supplied (Figure 2B).

DO NOT tighten the adjustment screws too tightly. You will have to

adjust the LM2000 later in the installation process.

Figure 1B

LM2000

Pipe

Bracket

Lock Washer

and Nut

Bolt

Pipe

Crankcase

Adjustment

Bolts

Figure 1A

Figure 2B

Crankcase

Base

Universal

Bracket

Threaded

hole

Adjustment

Bolts

Flat

Washer

Lock Washer

and Nut

Figure 2A

1-3/4 in.

(44 mm)

7-1/2 in.

(191 mm)

Slot, 29/64 in. (14 mm)

x 4-3/8 in. (111 mm)

3 places

6-11/16 in.

(170 mm)

Slot, 29/64 in. (14 mm)

x 2-3/8 in. (60 mm)

4 places

4-1/2 in.

(114 mm)

5-3/16 in.

(132 mm)

4-1/2 in.

(114 mm)

5-3/16 in.

(132 mm)

2-1/2 in.

(63.5 mm)

Hole 7/8 in.

(22 mm) dia.

1/4-20 NC

2 places

9/32 x 5/8 in.

(7 x 16 mm)

2 places

15000238

Pipe Bracket Kit

15010224

Universal Flange Kit

Additional Hardware

Supplied

(2) 1/4-20 x 7/8 inch

(22 mm) screws

(2) 1/4-20 x 1 inch

(25 mm) screws

(4) 1/4-20 hex nuts

(4) 1/4 inch (6 mm) dia.

split washer

Additional Hardware

Supplied

(2) 1/4-20 x 1/4 inch

(32 mm) bolts

(4) 1/4 inch dia. flat washer

(2) 1/4-20 hex nuts

(2) 5/16-18 x 1/4 inch

(32 mm) bolts

(4) 5/16 dia. flat washer

(2) 5/16-18 hex nuts

CAUTION:

Excessive vibration can cause over-

fill. Be sure mounting brackets are supported.

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Murphy Lube Level Maintainer LM2000 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Murphy Lube Level Maintainer LM2000